• Peter Frinchaboy- David Burch Rotorbreeze 2007

Collective Bounce

Pilots have asked me to please do something about aircraft that have a bounce with flat pitch running on the ground. I tell them to pull up slightly on the collective until the bounce is reduced. I could adjust the pitch change links to make the aircraft smoother, the problem is I have just changed the auto rotation RPM. I try to get them to understand auto rotation RPM is much more important than their short term comfort. The following article from Rotor Breeze explains why this happens. Peter Frinchaboy

From Rotorbreeze 2007:


Many Bell Helicopter models have leading edge pitch link installations on the main rotor hub. Each of these is subject to the vibration or ground bounce caused by the

Leading Edge Pitch Link Main Rotor to Mast Coupling Phenomenon. This has often been

mistakenly identified as being caused by Negative Pitch in the blades. This article

explains why leading edge pitch link rotors can have this bounce.

1. The main rotor mast bearing of all Bell aircraft has axial play by design. This

play is usually only observable when the mast does not have any weight from the

rotating controls or main rotor hub attached to it. This allows the mast to

move up and down axially on the mast bearing. It also allows some angular/side-

to-side movement at the top of the mast. For example: the model 407 has

maximum allowable axial play (up & down) of 0.065 inch.

2. The swashplate and support are mounted fixed to the top of the transmis sion. These controls have no vertical movement unless commanded by the con-

trol inputs from the pilot.

3. When the main rotor attains sufficient rpm and blade pitch, it lifts the mast and

rotating controls up the distance of the axial play in the mast bearing from the

static position (at the down position of the axial play) to the operating position (at the

top of the axial play). The point at which this happens is variable due to rpm and the basic minimum pitch angle (Auto-Rotation Speed Adjustment) set in the blades.

4. If the basic minimum pitch angle set in the blades is such that lift occurs as the

main rotor reaches operating rpm, the main rotor lifts. The leading edge pitch

links are fixed and as the rotor lifts, the pitch links decrease the blade pitch angle and

the rotor loses lift and moves back down the amount of the axial play.

When the rotor moves down, the pitch links now increase the blade pitch and

the rotor lifts back up and then the whole process keeps repeating. The process repeats at a frequency of the rotor rpm times the number of blades. This vibra-

tion or bounce in the aircraft can bequite severe and show a high lateral

vibration or a high vertical vibration on test equipment on the ground.

5. Usually a slight increase in collective pitch will cause the rotor to sustain its

lift and the vibration will go away. In many cases this indicates that the auto-

repeats at a frequency of the rotor rpm times the number of blades. This vibra-

tion or bounce in the aircraft can be quite severe and show a high lateral

vibration or a high vertical vibration on test equipment on the ground.

rotation rpm is set on the high side of the adjustment range. Normally, the

auto-rotation rpm should be decreased, which will increase the basic minimum

pitch angle set in the blades. This will cause the rotor to sustain lift at flat pitch

and at operational rpm (100%). Alternatively, the pilot must input a slight

amount of collective pitch at operational rpm (100%) to prevent the bounce.

Either method will stop the vibration and bounce. The following Bell Helicopter aircraft have leading edge pitch links. The table

shows the normal maximum axial play you will see in their respective mast bearings as

a guide to how much vertical movement the mast has.

Model Max Mast Axial Play Model Max Mast Axial Play

206A/B/B-3 0.037 inch 206L/L-1/L- 3 0.037/0.039 inch.

206L-3/L-4 0.058 inch OH-58A/C 0.037 inch

UH-1 (204 rotor) 0.038/0.040 inch 204/B 0.038/0.040 inch

205/A/A-1/B 0.038/0.040 inch 212 0.038/0.040 inch

210 0.038 inch 407 0.065 inch

412 0.040 inch

The 427 mast bearing has 0.085 inch axial play but is limited by design in its movement.

Note: the models UH-1(540 style rotor), all AH-1’s, 222/B/UT, 230, 214A/B/C, 214 ST, and

430 have trailing edge pitch links and are not subject

These numbers are for reference only and not for use as an inspection requirement for the bearings. Note

that some models have alternate bearings with different normal maximum axial play. Always consult the appropri-

ate maintenance manual for current allowables.

If you have questions on this subject,

feel free to contact me.

David C. Burch

Senior Customer Support Representative

Bell Helicopter Textron, Inc.

P.O. Box 460640

Aurora, CO 80046-0640

Phone: +1-(720)-870-7414

Facsimile: +1-(817)-278-0096